Ontrack and RAID data recovery.

Ontrack offers data recovery services for all major RAID architectures. This includes, RAID levels 0, 00, 1, 10, 1E, 1E0, 2, 3, 4, 5, 50, 5E, 5EE, 6 and 60. We also work for a large number of proprietary RAID arrays. The continuous development of our software tools ensures that we use the latest state-of-the-art and proprietary techniques to achieve the best possible data recovery. In addition, the research & development team assists our engineers in data recovery when they are confronted with unusual proprietary RAID arrays, through custom tools created especially for the occasion.

We are recommended by most RAID vendors such as HP, Compaq, Dell, Adaptec, IBM, Intel, Promise, LSI Logic, Mylex, Xiotech and Netsan. All have their own RAID configuration, a specific data block size, and a parity size and unique symmetry.

Our RAID recovery capabilities do not just stop at NTFS, our skills also extend to MAC, UNIX, FAT and VMware RAIDs.

RAID data recovery


The different types of RAID.

RAID configuration, including the number of disks used, determines the type. As a reminder, the RAID that stands for Redundant Array of Independent Disks or Redundant Independent Disk Array is a storage solution that distributes data across multiple small disks that together form a single system. In addition to being less expensive, this device has a high level of performance and data security as RAID tolerates breakdowns better.

Today, there are nearly twenty types of RAID, if not more including configurations sometimes considered obsolete- among which is the RAID 2. Of all these RAID configurations, the most common are the RAID 0, RAID 1, RAID 10, RAID 2, RAID 3 and 4, RAID 5 or RAID 6.

RAID 0 is a system that uses only two disks and provides fast access to data. The RAID 1 also uses two disks and writes duplicate information. If one of the disks is damaged, you will find your data on the other. To benefit from the performance of RAID 0 and the security offered by RAID 1, RAID 5 was created. With a good distribution of data, RAID 5 combines speed and fault tolerance. The RAID 6 has the same advantages as RAID 5, but with the added bonus of better writing speed.


RAID 0.

RAID 0 is the classic data stripping configuration, where data is written across all drives resulting in faster access. However, this performance carries a risk, if one or more disks cause a disaster in a RAID 0, then a serious loss of data can occur. The diagram below shows how the data is distributed across the matrix.

An example of a data recovery situation: a file was created that occupied data stripes 1 – 4, if drive 2 were to fail and the 2nd stripe lost, the file would most likely become corrupted. Another way to look at it would be if one drive fails, the largest possible good file would have to be smaller than the combined size of the remaining stripes.

RAID 0

RAID 0 Configuration

RAID 1.

This is the RAID level that sets up disk mirroring; the data on the primary disk is duplicated onto the other. There are no performance gains for this RAID, but if one drive fails, then you will have a backup on the second one.

RAID 1

RAID 1 Configuration

RAID 0+1 and 1+0.

To gain performance and/or additional redundancy the standard RAID levels can be combined to create hybrid or nested RAID levels, RAID types that provide redundancy are typically combined with RAID 0 to boost performance.

As you can see from the diagrams below, these two levels of RAID are a combination of RAID 0 and RAID 1. The difference between the two is the actual position of the RAID array, shown by the diagrams where the bands are in bold.

RAID 01 is configured so that RAID 0 is a mirror copy.

The advantage is that when a drive fails in one of the level 0 arrays, the missing data can be transferred from the other array. However, adding an extra hard drive to one stripe requires you to add an additional hard drive to the other stripes to balance out storage among the arrays.

A disadvantage for this configuration is that is cannot recover from two simultaneous drive failures, unless the drives are from the same data stripe. In the diagram; if drives 1 and 5 failed the RAID could be rebuilt, but if 1 and 4 failed it would result in data loss.

RAID 01 Configuration

RAID 10.

RAID 10 is configured so that the RAID 0 is split across two RAID 1 arrays.

A big advantage to RAID 10 is all but one drive from each RAID 1 array could fail without any data loss. However, if the failed drive is not replaced, the single working drive in that array becomes a single point of failure for the entire system, if that last drive goes all data within the array is lost.

The RAID nesting technique can be used for other RAID levels as well, most commonly on RAID 5 but it can also be applied to other levels like 3 and 6, producing levels such as 50, 51, 60, 61, 30 and 03.

RAID 10


RAID 2.

RAID 2 comprises of data striping at a bit level with a dedicated parity drive. This level uses hamming error detection codes and is intended for use on drives that do not have built-in error detection. For this reason, RAID 2 is not commonly used anymore.


RAID 3 and 4.

RAID 3 and 4 both use striping with a dedicated parity drive, the difference between the two is that RAID 3 stripes at the byte level while RAID 4 stripes at the block level. RAID 3 is seldom used these days due to the poor performance of byte level striping, RAID 4 is better with block level striping but still suffers slower write performance due to the parity having to be updated on every write.

RAID 3 and 4 Configuration

RAID 5

RAID 5 is generally considered to be the best compromise between fault tolerance, speed and cost. The system divides the data in the same way as a RAID 0, but also distributes the parity data on all the hard disks that compose it. Each vendor has its own specific way of distributing parity information on disks, but it will almost always be one of these four ways: left asymmetric, left symmetric, right asymmetric and right symmetric. In the following diagram you can see how the location of the parity data is distributed over the disks.

The direction of parity is simple to identify, as you can see it "moves" both right and left. In asymmetric RAIDs the data strips ignore parity, they skip it until they reach the next available space. Symmetric RAIDs handle data strips in a slightly more complex way, once the data encounters a parity block, they move sideways and down to the next stripe set.

RAID 5 configuration

RAID 6

The RAID 6 system is an extension of the RAID 5: it performs the same data distribution and adopts a similar division of parity, but generates an additional data block for each stripe. This way even if two disks were to fail simultaneously the RAID would not suffer data loss. In smaller RAIDs, the possibility of two hard drives failing simultaneously is reduced, but as the size of the RAID array increases, the chance of failures increases. 

As for the performances, they are very similar to those of RAID 5: the writing speed is high, because the data and parity blocks can be written on all disks, but the read access is slow due to the delay generated by the jump of two parity series.

RAID 6 Configuration

  

Start your data recovery now with a free consultation.

Contact our team of experts. Ontrack accommodates everyone – from the largest government or enterprise organization to an individual who may have lost their digital photos and everyone in between.

Step 1

Device Type
Step 2

Data Loss Reason
Step 3

Details & Evaluation

What type of device do you need data recovery for?

What is the main reason for your data loss?

Additional comments

* The free evaluation may not be possible. Please contact us or enter your details and we will contact you as soon as possible. In case of assistance please call: 855.652.2387

1. Contact details

2. Shipping details

Would you like to start your FREE evaluation and arrange FREE shipping?:
Complimentary shipping is not available in your country.